Flower wilt remedies
In the process of growth and development of potted flowers, wilting phenomenon often occurs due to environmental factors and the flowers themselves, and the growth of flowers is thus inhibited or even withered. The reasons for the wilting of flowers and the remedial measures are as follows: 1, drought and flood. The long-term drought of the flowers failed to water in time, wilting from the top, and the cortex of the branches shrank until the whole plant died. At this time, it is necessary to spray water on the foliage and surrounding environment of the flowers to maintain high environmental humidity, and avoid using large amounts of low-temperature water to irrigate the soil under high temperature conditions. 2, Shui Ye. If the water content in the soil is too large, the roots of the plants will be blocked by breathing and suffocate. The branches and leaves will not receive the water supply from the roots, resulting in wilting and dead. For the flowers to be protected from direct exposure to strong light and strong winds, cut off some tender shoots and leaves to reduce water evaporation. Remove 1/3 of the wetted potted soil, add dry soil and replant. Spray the leaves with water and spray 1 thin liquid fertilizer every 3 days. After 10 days of conservation, the damaged flowers can be recovered. 3. Wind blows: New shoots of flowers occur, especially when spring shoots grow in large numbers. When strong light and strong winds are encountered, wilting often occurs. At this time, shading, sheltering, and spraying on the leaves should be adopted to prevent the shoots from losing water and wilting. 4. Enthusiasm: Summer flowers like a cool environment, if placed in a strong light, high temperature, the leaves will appear wilting roll, even withered off. Immediately put it in a moist, ventilated, cool place. 5. Leng Biao: In winter, the temperature fluctuates greatly, and the night temperature suddenly drops below 10°C. Fusang, jasmine and rhododendron are other flowers. The leaves will be wilting and lose luster in the morning, and gradually recover after noon temperature rises. Short-term cold chilling has little effect on flowers, but it should be kept warm. 6. Fat man. When the fertilizer concentration in the flower soil is too high, the water in the flower plant will permeate into the soil (that is, reverse osmosis), which is commonly known as burning root, causing the flowers to wilt and die. The topsoil in the pots should be removed and water should be poured so that excess fertilizer flows out of the bottom of the pots with the water, and a layer of prime soil is covered on the surface of the pots. At the same time, we must take measures such as shading and spraying water on the damaged flowers to maintain the life of the flowers and leaves and return to normal after 10-20 days. 7, insects. In the case of serious damage to both the calf and the genus, it can damage the transmitting tissue of the trunk or main branch of the flower, resulting in partial or whole wilting and withering. The wilting caused by pests is difficult to recover. The precious flowers can cut the branches and carry out cuttings. Or grafted. NVR Security Camera Kits System
NVR WiFi cameras can be added to NVRs if they are in the same LAN. Here we'll guide you to finish this process following the steps below.Step 1: Connect the camera to your router via WiFi by configuring WiFi settings for the WiFi camera. NVR Security Camera Kits System,NVR WiFi cameras,Connect the camera,WiFi camera,PoE NVR to the LAN Shenzhen Fuvision Electronics Co., Ltd. , https://www.szsolarcamera.com
Step 2: Connect your PoE NVR to the LAN port of the router.Step 3: Open the monitor of your NVR, then select Channel Settings > IP channel. Check Auto Add and click Scan. Then the WiFi camera will show up in the list. Assign a channel for it if necessary.NVR WiFi cameras can be added to NVRs if they are in the same LAN. Here we'll guide you to finish this process following the steps below.Step 1: Connect the camera to your router via WiFi by configuring WiFi settings for the WiFi camera.
Step 2: Connect your PoE NVR to the LAN port of the router.Step 3: Open the monitor of your NVR, then select Channel Settings > IP channel. Check Auto Add and click Scan. Then the WiFi camera will show up in the list. Assign a channel for it if necessary.
NVR WiFi cameras can be added to NVRs if they are in the same LAN. Here we'll guide you to finish this process following the steps below.Step 1: Connect the camera to your router via WiFi by configuring WiFi settings for the WiFi camera.
Step 2: Connect your PoE NVR to the LAN port of the router.Step 3: Open the monitor of your NVR, then select Channel Settings > IP channel. Check Auto Add and click Scan. Then the WiFi camera will show up in the list. Assign a channel for it if necessary.
NVR WiFi cameras can be added to NVRs if they are in the same LAN. Here we'll guide you to finish this process following the steps below.Step 1: Connect the camera to your router via WiFi by configuring WiFi settings for the WiFi camera.
Step 2: Connect your PoE NVR to the LAN port of the router.Step 3: Open the monitor of your NVR, then select Channel Settings > IP channel. Check Auto Add and click Scan. Then the WiFi camera will show up in the list. Assign a channel for it if necessary.